200 Watt 10L Industrial Ultrasonic Washer For Bike Chain With Power
Adjustable
How Does Whale cleen sonic Industrial Ultrasonic Washer Work?
Ultrasonic cleaners have generators that produce voltage, which in
turn produces high frequencies that alternate to create high and
low pressure within the cleaning chamber. When you place a dirty
bike chain into the chamber cleaning solution, low pressure sound
waves form little bubbles on the chain's surface and then collapse
when the high pressure cycle kicks in. As they pop, the bubbles
create little shock waves that essentially scrub the chain,
cleaning dirt and oil from it.
Specification Of Z-04:
| Model | Z-04 |
| Ultrasonic Frequency | 40,000 Hz |
| Tank Material | SUS304 |
| Tank Capacity | 10 L |
| Timer | 1-30minutes ,Digital timer |
| Power Supply | AC 100 ~ 120V, 50 / 60Hz
AC 220 ~ 240V, 50 / 60 Hz |
| Ultrasonic Power | 0~200W |
| Heating Power | 450 W , Digital Heating |
| Unit Size | 325x265x280 mm ( L x W x H ) |
| Tank Size | 300x240x150 mm ( L x W x H ) |
| Package Size | 435x360x350 mm ( L x W x H ) |
| N.W. | 7.4 kg |
| G.W. | 8.5 kg |
Customer's Cleaning Feedback:
How To Clean Your Bike Parts With Whale cleen sonic Industrial
Ultrasonic Washer?
1. Get Your Sonic Cleaner Ready – Fill your ultrasonic unit to the
“fill line” with hot, clean water. Next, add your cleaning
concentrate to around 10% concentration. This can be adjusted up or
down depending on how dirty your parts are. Insert your cleaning
basket, and let the unit run empty for a cycle or two. This will
allow the tank to come to temperature, as well as “de-gas” the
cleaning solution.
2. Clean Your Bike Parts – First, place your bike parts into the
cleaning basket. Make sure your parts are arranged in such a way
that they are completely submerged when lowered into the cleaning
tank. Once the basket and parts are in the tank, choose your cycle
time (if applicable) and hit go! In general, it shouldn’t take more
than 5 to 10 minutes to fully clean your parts. Once the cycle is
completed, remove your parts from the basket, and allow to air dry,
or if available, blow dry.
TIP: Your tank of ultrasonic cleaning solution can be used more
than once! A good indication of when you need to replace your
solution with a new batch is when cleaning time begins to increase
to acheieve the same result.
3. Ultrasonic Relubrication – Using an ultrasonic parts washer to
re-lubricate your bike parts may sound far fetched, but the process
is quite simple. First, have your ultrasonic cleaner ready with a
tank of clean, hot water, filled to JUST UNDER the fill line. Next,
place around 2 to 3 inches of lubricant in your lube pan, then
place the lube pan in such a way that the bottom inch of the lube
pan is submerged around an inch or so in the tank water. Many
“solid trays” have flanges on the side to facilitate this purpose.
Finally, run your ultrasonic unit as normal, as if you were
cleaning parts.
The way this works is that ultrasonic energy will actually pass
through the tank of water, pass through the bottom of the lube pan,
and into the lubricant within, thus sonifying it. The same process
that cleans even microscopic nooks and cranies will now shove
lubricant into those same areas!
After a full cycle, remove your parts from the lube pan, and allow
them to drip access lubricant back into the pan. Finally, wipe any
remaining lubricant from your parts, as over lubrication can
attract abrasive soils over time.
Whatever cleaning schedule you set up, you’ll find that the life of
your bike is extended, and you’ll get more hours of trouble-free
riding by keeping your gear clean and lubricated.
