22 Liter 400Watt Medical Ultrasonic Cleaner With 600W Heating Power
How Whale Cleen sonic Medical Ultrasonic Cleaner Works?
Ultrasonic cleaning uses high frequency sound waves to generate
cavitation in the liquid. The resulting energetic bubble action
penetrates blind holes, cracks, and recesses to thoroughly remove
all traces of contamination adhering or embedded on the solid
surface. Contaminants can include blood,tissue,body fluid,dust,
dirt, oil, pigments, grease, polishing compounds, flux agents,
soot, and more.
Detail Information Of Z-S08:
| Model | Z-S08 |
| Ultrasonic Frequency | 40,000 Hz |
| Tank Material | Stainless Steel SUS304 |
| Tank Capacity | 22 L |
| Timer | 1-30minutes ,Digital timer |
| Power Supply | AC 100 ~ 120V, 50 / 60Hz
AC 220 ~ 240V, 50 / 60 Hz |
| Ultrasonic Power | 500W |
| Heating Power | 600 W , Digital Heating |
| Tank Size | 500×300×150 mm ( L x W x H ) |
| Unit Size | 530×325×285 mm ( L x W x H ) |
| Package Size | 635×405×340mm( L x W x H ) |
| Longest Gun You Can Clean | 480mm |
| N.W. | 12.1kg |
| G.W. | 15.6kg |
If this model is not suitable for you, please check other in below
chart.
| Model | Tank size | Unit size | Volume | Actual ultrasonic power | Rated ultrasonic power | Ultrasonic frequency | Heating power | Timer | Heating temperature |
| LxWxH(mm) | LxWxH(mm) | (L) | (W) | (W) | (kHz) | (W) | (MIN) | (℃) |
| Z-S008 | 150x85x65 | 175x110x125 | 0.8 | 30 | 30 | 40 | no | 1-30 | no |
| Z-S01 | 150x135×100 | 175x160x210 | 2 | 50 | 60 | 40 | 150 | 1-30 | 0-80 |
| Z-S02 | 240x135x100 | 265x165x220 | 3.2 | 100 | 120 | 150 |
| Z-S03 | 300x150x100 | 325x180x225 | 4.5 | 150 | 180 | 300 |
| Z-S031 | 300x150x150 | 325x180x280 | 6.5 | 150 | 180 | 300 |
| Z-S04 | 300x240x150 | 325x265x280 | 10.8 | 200 | 240 | 450 |
| Z-S06 | 330x300x150 | 360x325x285 | 15 | 300 | 360 | 450 |
| Z-S08 | 500x300x150 | 530x325×285 | 22 | 400 | 480 | 600 |
| Z-S10 | 500x300x200 | 530x325x325 | 30 | 500 | 600 | 600
|
Customer's Feedback From USA:
Cleaning Steps For Surgical Instrument:
In all cases manufacturers’ instructions should be followed when
using an ultrasonic cleaning process. These are representative
steps.
Fill the ultrasonic cleaning tank with an approved medical
instrument cleaning solution following dilution instructions
provided. Turn the cleaner on to start the degassing process. This
step removes entrained air in new solutions that interferes with
the efficiency of cavitation and takes approximately 10 minutes.
In the meantime:
- Segregate instruments by alloy or composition to avoid potential
damage (Chromium plated instruments should not be cleaned
ultrasonically)
- Instruments with movable parts should be disassembled to facilitate
cleaning
- Place the instruments the ultrasonic cleaner’s mesh basket, taking
care that they do not come in contact with each other
- Cannulated or lumened instruments should be positioned to insure
interiors are wetted with the cleaning solution. In some instances
placing them on an angle will facilitate this
- Set the control panel per manufacturers’ instructions and start the
cleaning process
At the end of the cycle, remove the instruments from the ultrasonic
cleaning bath and thoroughly rinse them to remove all traces of the
cleaning solution. Deionized water rinses will avoid spotting. If
the instruments are not to be immediately disinfected and
sterilized be certain that they are thoroughly dried and protected.
Part reassembly can occur after sterilization.
Procedures should be in place to guide the replacement of used
ultrasonic cleaning solutions. In some instances it is recommended
that solution be drained and tanks thoroughly cleaned and dried
after each ultrasonic cleaning cycle. Most solutions available
today are biodegradable, which facilitates disposal but local
authorities should be consulted on proper practices.
